Can-Am Commander Turn Signals
Can-Am Commander Turn Signals
Looking for Can-Am Commander turn signals to make your Can-Am Commander street legal. You have come to the right place! Hence, we have developed D.O.T. approved Can-Am Commander turn signals. To clarify, our kits will help you make your UTV (side-by-side) street legal.
For instance, having a Street Legal Can-Am Commander UTV is just awesome. In other words, with the right Can-Am Commander turn signals, you can really tackle every type of terrain. That is to say you can go from pavement, to off-road trails and back again. Subsequently, we build the Can-Am Commander turn signals and accessories you need. For instance, D.O.T. approved LED Turn Signal Kits, Horn Kits and LED Lighted License Plate Brackets. As a result you can safely and effectively ride on the streets in your area.
D.O.T. Approved Can-Am Commander Turn Signals
The Can-Am Commander Turn Signals are intended to help you convert your off-road UTV (side-by-side) to a street legal ride in many states. In addition our kits include parts that are actually D.O.T. approved items. That is to say, you will need these while converting your off-road recreational vehicle to street legal status. Meanwhile, be careful as some of our competitors out their Do Not use D.O.T. approved parts. Consequently, they will sell you a Can-Am Commander turn signals kit that it is not D.O.T. approved.
All states have their own D.O.T. requirements for street legal equipment. Most importantly, check with your local Department of Motor Vehicles (DMV) or Motor Vehicle Division (MVD). Certainly get the information for your local requirements. Furthermore, most states require a Horn (120 db+), Lighted License Plate and Turn Signals. However, not all states require turn signals (hand signals are ok). Above all, we highly recommend turn signals for your added safety. That is to say, we know through experience that some drivers DO NOT know what hand signals are.
Why Our Can-Am Commander Turn Signals are Completely Independent
I get asked a few times every month, why don’t you use the Can-Am Commander rear OEM lights for the rear turn signals? The answer is very simple. I developed my Turn Signal Kits (TSK) to be completely independent for THREE main reasons. ONE, you do not want any possible feedback from the LED Electronic Flasher into the ECU of your UTV. Consequently, electronic feedback can cause problems with your ECU and they are very expensive to replace. TWO, you do not want to affect (invalidate) your manufactures warranty by tapping into any existing OEM lights or wiring. THREE, you want both rear stop lights when activating the turn signals (like our automobiles), not just one. As a result, with all my different Can-Am Commander turn signal kits you will never have these concerns or issues.
Can-Am Commanderer Turn Signals
Column Mounted (TSS) Hardware Notes
2011-21 Can-Am Commander / MAX models (TSS) Mounting Hardware Notes
The 2011-21 Can-Am Commander / MAX models use our Custom Turn Signal Switch (TSS) Mounting Bracket. Furthermore, this custom bracket was designed to mount the turn signal switch below the instrument cluster on the steering column. Used with our stock #104 or #107-SM LED Turn Signal Kits. As a result, order from the drop down box Turn Signal Switch Mounting Hardware.
- 11-21 Can-Am Commander / MAX TSS Bracket
Can-Am Commander Turn Signals
SM LED Turn Signal Kit
(Stock# 104) / (Base Price: $129.95)
The SM LED Turn Signal Kit with surface mount Super Bright D.O.T. approved LED lights (no brackets required). In addition, our SM LED light kit comes with 2 surface mounted ¾” inch amber (front) LED lights. Also, 2 surface mounted ¾” inch red (rear) LED lights. However, you can add additional lights to give your Can-Am Commander a custom look.
Can-Am Commander Turn Signals Specifications
This SM LED light kit comes with a column mounted turn signal switch. First of all, it has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). Secondly, the turn signal switch has a pull out flare tab for the 4-way hazard lights. Finally, it comes with the hardware to mount it to your steering column.
The four Surface Mounted LED Super Bright Lights are ¾” inch round with an attached rubber grommet for quick mounting. Secondly, they are surface mounted LED’s with a slim-line design for mounting in small spaces (no brackets required). Thirdly, these SM LED’s are D.O.T. approved. In addition, they meet the P2PC requirements for 45 degree mounting and provide superior light output. Furthermore, they have a Space Saving Design, Hi Impact Acrylic Lens and Housing. Finally, they have Completely Resin Sealed Electronics to eliminate corrosion.
This special LED Flasher has the 3 pin connections for LOAD, PILOT and POWER. Also, the electronic LED flasher is quite, no annoying clicking sounds.
Our kit includes: 2 Amber and 2 Red SM LED super bright lights with grommets. Secondly, the Turn Signal Switch with the hardware to mount it to your steering column (see TSS mounting hardware notes above). Also, the LED Flasher with mounting hardware. Furthermore, an ATC in-line fuse holder with a 3 amp fuse. In addition, the mounting installation instructions with wiring instructions & diagram. Most importantly, with our Can-Am Commander turn signals you get all the help and support you need from EZ Turn Signal Kits.
Important Note
Note FYI: I have heard people say that a column mounted Turn Signal Switch (TSS) is in the way of you entering and exiting the unit, not true! Secondly, they say you will bump the TSS lever with your legs and even break that lever, again not true! In other words, I am 6’3″ and 250 pounds, I have never bumped the TSS and I use my units multiple times a day. Finally, I have sold thousands of the column mounted TSS and never had a customer complain about bumping or breaking one.
Can-Am Commander Turn Signals Installation
This kit can be easily installed, it does not go into any factory wiring and above all it will not void your manufactures warranty! In addition, each wire has a different color and the wiring diagram shows where each colored wire goes. Above all, I include my phone number and e-mail address with the instructions. Therefore, if you have any questions about your installation you can contact me.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. Meanwhile, the Motor Vehicle Department and your local police departments will be impressed. Most noteworthy, everyone who rides on the street or off road (dunes/congested areas), should have turn signals for their added safety.
The SM LED Turn Signal Kit will fit all of the Can-Am Commander UTV side-by-side models (check the TSS mounting hardware notes above).
In addition you can customize the UTV with Double or Triple lights. As a result, order from the drop down box Light Options: Double Lights: 4 Amber & 4 Red lights or Triple Lights: 6 Amber & 6 Red lights.
Likewise you may want amber lights front and rear. As a result, order from the drop down box Light Options: Amber Kit: All 4 Amber lights or Double Lights All Amber: 8 Amber lights or Triple Lights All Amber: 12 Amber lights.
Can-Am Commander Turn Signals Options
SM LED Turn Signal Kit #104 Options:
Option1 – Double or Triple Lights for a custom look!
Option2 – Turn Signal Switch (TSS) mounting hardware for your particular year, make and model.
Option3 – UTV Wire and Connector Kit, to clarify this kit will make it easy to connect your turn signals.
Option4 – Dash Indicators for those that want one or two dash indicators.
You can order whatever options you want with your Turn Signal Kit by using the drop down (∇) menus.
Choose Your Options & Add to Cart
Choose Your Options & Add to Cart
Customer Reviews SM LED Turn Signal Kit #104
Can-Am Commander Turn Signals
SM LED Running Lights & Turn Signal Kit
(Stock# 107-SM) / (On Sale/Base Price: $149.95)
This is a 12 volt LED Running Lights & Turn Signal Kit with surface mount Super Bright D.O.T. approved LED lights (no brackets required). In addition, our LED running lights & turn signal light kit comes with 2 surface mounted ¾” inch amber (front) LED lights. Also, 2 surface mounted ¾” inch red (rear) LED lights. However, you can add additional lights to give your Can-Am Commander a custom look.
Can-Am Commander Turn Signals Specifications
This SM LED running lights & turn signal kit comes with a column mounted turn signal switch. First of all, it has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). Secondly, the turn signal switch has a pull out flare tab for the 4-way hazard lights. Furthermore, it comes with the hardware to mount it to your steering column.
The four Surface Mounted LED Dual Mode Super Bright Lights are ¾” inch round with an attached rubber grommet for quick mounting. Secondly, they are surface mounted LED’s with a slim-line design for mounting in small spaces (no brackets required). Furthermore, they have 3 lead wires each, one for ground, one for normal mode (running) and one for high mode (signals). In addition, they meet the P2PC requirements for 45 degree mounting and provide superior light output. Furthermore, they have a Space Saving Design, Hi Impact Acrylic Lens and Housing. Finally, they have Completely Resin Sealed Electronics to eliminate corrosion.
This special LED Flasher has the 3 pin connections for LOAD, PILOT and POWER. Also, the electronic LED flasher is quite, no annoying clicking sounds.
The Running Light Switch is a LED waterproof illuminated rocker switch. Above all, it is easy to install, vibration resistance, and will illuminate when activated.
Can-Am Commander Turn Signals
Our SM LED Running Lights & Turn Signal Kit includes. 2 Amber and 2 Red SM LED Dual Mode super bright lights with grommets. Secondly, the Turn Signal Switch and the hardware to mount it to your steering column (see TSS mounting hardware notes above). Also, a waterproof LED rocker switch and special LED Flasher with mounting hardware. Furthermore an ATC in-line fuse holder with a 3 amp fuse. In addition, the mounting installation instructions with wiring instructions & diagram. Most importantly, with our Can-Am Commander turn signals you get all the help and support you need from EZ Turn Signal Kits.
Important Note
Note FYI: I have heard people say that a column mounted Turn Signal Switch (TSS) is in the way of you entering and exiting the unit, not true! Secondly, they say you will bump the TSS lever with your legs and even break that lever, again not true! In other words, I am 6’3″ and 250 pounds, I have never bumped the TSS and I use my units multiple times a day. Finally, I have sold thousands of the column mounted TSS and never had a customer complain about bumping or breaking one.
Can-Am Commander Turn Signals Installation
This kit can be easily installed, it does not go into any factory wiring and above all it will not void your manufactures warranty! In addition, each wire has a different color and the wiring diagram shows where each colored wire goes. Above all, I include my phone number and e-mail address with the instructions. Therefore, if you have any questions about your installation you can contact me.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. Meanwhile, the Motor Vehicle Department and your local police departments will be impressed. Most noteworthy, everyone who rides on the street or off road (dunes/congested areas), should have turn signals for their added safety.
The SM LED Running Lights & Turn Signal Kit will fit all of the Can-Am Commander UTV side-by-side models (check the TSS mounting hardware notes above).
In addition you can customize the UTV with Double or Triple lights. As a result, order from the drop down box Light Options: Double Lights: 4 Amber & 4 Red lights or Triple Lights: 6 Amber & 6 Red lights.
Can-Am Commander Turn Signals Options
SM LED Running Lights & Turn Signal Kit #107-SM Options:
Option1 – Double or Triple Lights for a custom look!
Option2 – Turn Signal Switch (TSS) mounting hardware for your particular year, make and model.
Option3 – UTV Wire and Connector Kit, to clarify this kit will make it easy to connect your turn signals.
Option4 – Dash Indicators for those that want one or two dash indicators.
You can order whatever options you want with your Turn Signal Kit by using the drop down (∇) menus.
Choose Your Options & Add to Cart
Choose Your Options & Add to Cart
Customer Reviews SM LED Running Lights & Turn Signal Kit #107-SM
Can-Am Commander Turn Signals
UTV / ATV Toggle Switches
LED Turn Signal Kit
with Emergency Flashers
(Stock# 604) / (Base Price: $99.95)
This is a 12 volt Toggle Switches LED Turn Signal Kit with surface mount Super Bright D.O.T. approved LED lights (no brackets required). Our Toggle Switches (TS) LED light kit comes with 2 surface mounted ¾” inch amber (front) LED lights. In addition, 2 surface mounted ¾” inch red (rear) LED lights. However, you can add additional lights to give your Can-Am Commander a custom look.
Can-Am Commander Turn Signals Specifications
Our Toggle Switches LED Turn Signal Kit comes with two toggle switches. In addition, 2 LED indicator lights for the Turn Signals and 4-way Emergency Flashers (hazard warning).
The four Surface Mounted LED Super Bright Lights are ¾” inch round with an attached rubber grommet for quick mounting. Secondly, they are surface mounted LED’s with a slim-line design for mounting in small spaces (no brackets required). In addition, they meet the P2PC requirements for 45 degree mounting and provide superior light output. Furthermore, they have a Space Saving Design, Hi Impact Acrylic Lens and Housing. Finally, they have Completely Resin Sealed Electronics to eliminate corrosion.
This special LED Flasher has the 3 pin connections for LOAD, PILOT and POWER. Also, the electronic LED flasher is quite, no annoying clicking sounds.
Our toggle switches LED turn signal kit includes. 2 Amber and 2 Red SM LED super bright lights with grommets. Secondly, two (2) Toggle Switches with Rubber Boots. In addition two (2) LED indicator lights for the turn signals and 4-way emergency flashers. Also, the LED Flasher with mounting hardware. Furthermore, an ATC in-line fuse holder with a 3 amp fuse. Finally, the mounting installation instructions with wiring instructions & diagram. Most importantly, with our Can-Am Commander turn signals you get all the help and support you need from EZ Turn Signal Kits.
Can-Am Commander Turn Signals Installation
This kit can be easily installed, it does not go into any factory wiring and above all it will not void your manufactures warranty! In addition, each wire has a different color and the wiring diagram shows where each colored wire goes. Above all, I include my phone number and e-mail address with the instructions. Therefore, if you have any questions about your installation you can contact me.
These turn signal toggle switches are very nice and easy to operate. Meanwhile, the Motor Vehicle Department and your local police departments will be impressed. Most noteworthy, everyone who rides on the street or off road (dunes/congested areas), should have turn signals for their added safety.
Note: The steering column mounted turn signal switch is the safest and easiest to operate. Most Importantly, we always recommend that you install a steering column mounted turn signal switch kit. To clarify, we recommend our (stock# 104, or 107-SM) on a UTV side-by-side (if you have the steering column space), for your added safety. In other words, a steering column mounted turn signal switch is located in the same area as your automobile. To clarify, it comes natural for activating while keeping your eyes on the road.
The Toggle Switches LED Turn Signal Kit will fit all years for the Can-Am Commander models.
In addition you can customize the UTV with Double or Triple lights. As a result, order from the drop down box Light Options: Double Lights: 4 Amber & 4 Red lights or Triple Lights: 6 Amber & 6 Red lights.
Likewise you may want amber lights front and rear. As a result, order from the drop down box Light Options: Amber Kit: All 4 Amber lights or Double Lights All Amber: 8 Amber lights or Triple Lights All Amber: 12 Amber lights.
Can-Am Commander Turn Signals Options
Toggle Switches LED Turn Signal Kit #604 Options:
Option1 – Double or Triple Lights for a custom look!
Option2 – TS Wire and Connector Kit, to clarify this kit will make it easy to connect your turn signals.
You can order whatever options you want with your Turn Signal Kit by using the drop down (∇) menus.
Choose Your Options & Add to Cart
Choose Your Options & Add to Cart
Customer Reviews Toggle Switches LED Turn Signal Kit #604
Please let us know if you have any questions or need assistance, you can call us at (843) 725-8890 or send an e-mail to Jake@LEDTSK.com
In addition, have you seen our Can-Am Street Legal Kits?
Have you seen the new Can-Am models?