LED Turn Signal Kit #105

LED Turn Signal Kit 105

This is a 12 volt LED Turn Signal Kit 105 with 2 Amber (front) and 2 Red (rear) or your choice of all Amber D.O.T. approved LED lights. Our LED turn signal kit 105 comes with two 4″x 2″ inch rectangular amber (front) LED lights. In addition, two 4″x 2″ inch rectangular red (rear) LED lights. However, you can substitute the rear lights for the ¾” SM LED lights to give your UTV a custom look.

LED Turn Signal Kit 105 Specifications

This LED turn signal kit 105 comes with a turn signal switch. First of all, it has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). Secondly, the turn signal switch has a pull out flare tab for the 4-way hazard lights. Furthermore, it comes with the hardware to mount it to your steering column.

The four LED Lights are 4”x 2” rectangular with 16 (LED) Light Emitting Diodes each. Secondly, they have a polycarbonate lens & housing. Finally, they are hard wired with encapsulated electronics to eliminate corrosion. Likewise, you can substitute the 4″x 2″ (rear) LED lights for the ¾” SM LED lights to add a custom look.

This special LED Flasher has the 3 pin connections for LOAD, PILOT and POWER. Also, the electronic LED flasher is quite, no annoying clicking sounds.

Our LED turn signal kit 105 includes: 2 Amber and 2 Red or all Amber D.O.T. approved LED lights. Secondly, the turn Signal Switch with hardware to mount it to your steering column (see TSS mounting hardware). Also, the LED Flasher, ATC in-line fuse holder, 3 amp fuse, self tapping screws for mounting the lights and flasher. In addition, the mounting installation instructions with wiring instructions & diagram. Most importantly, with our LED Turn Signal Kit 105 you get all the help and support you need from EZ Turn Signal Kits.

LED Turn Signal Kit 105 Important Note

Note FYI: I have heard people say that a column mounted Turn Signal Switch (TSS) is in the way of you entering and exiting the unit, not true! Secondly, they say you will bump the TSS lever with your legs and even break that lever, again not true! In other words, I am 6’3″ and 250 pounds, I have never bumped the TSS and I use my units multiple times a day. Finally, I have sold thousands of the column mounted TSS and never had a customer complain about bumping or breaking one.

LED Turn Signal Kit 105 Installation

This kit can be easily installed, it does not go into any factory wiring and above all it will not void your manufactures warranty! In addition, each wire has a different color and the wiring diagram shows where each colored wire goes. Above all, I include my phone number and e-mail address with the instructions. Therefore, if you have any questions about your installation you can contact me.

This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Most noteworthy, everyone who rides on the street or off road (dunes/congested areas), should have turn signals for their added safety.

The LED Turn Signal Kit 105 will fit most of the UTV side-by-side full-size models (check the TSS mounting hardware).

In addition you may like amber lights front and rear, order from the drop down box Light Options: Amber Kit: All 4 Amber lights.

Likewise you can substitute the 4″x 2″ (rear) LED lights for the ¾” SM LED lights to add a custom look. Order from the drop down box Light Options: 2 Amber ¾” LED Lights or 2 Red ¾” LED Lights or 4 Amber ¾” LED Lights or 4 Red ¾” LED Lights.

LED Turn Signal Kit 105 Options

We have some Custom Kit Brackets, UTV Wire & Connector Kit and LED Dash Indicators. Therefore, you may want to use these with your LED Turn Signal Kit. That is to say, any of these options purchased with your LED turn signal kit 105, will save you time & money!

Your choice of lights to make your UTV have a custom look.
Turn Signal Switch (TSS) mounting hardware for your particular year, make and model.
The 09-20 Ranger 800-900-1000 XP/HD/HO/Crew/6×6/Diesel/570 Full-size Front Flare Brackets (FFB). First of all these will give your 2009-2010 Ranger 500 or 2009-2019 Ranger 800/900/1000 XP, HD, HO & Deluxe models an OEM look. Secondly these will give your 2010-2019 Ranger 800/900/1000 Crew & 6×6 models or 2011-2018 Ranger Diesel models an OEM look. Finally these will give your 2015-2020 Ranger 570 Full-size models an OEM look. Note1: These FFB’s DO NOT work on the Ranger Mid-size EV/ETX/400/500/570/800 models. Note2: The 2018-20 Ranger 1000 XP does not have front flare openings in their new front design. Note3: Also, the 2019-20 Ranger Crew XP 1000 does not have front flare openings in their new front design.
If you don’t have a rear bumper, you might want to use our Rear T-Brackets (4″ x 2″ lights only).
UTV Wire and Connector Kit, to clarify this kit will make it easy to connect your turn signals.
Dash Indicators for those that want one or two dash indicators.

You can order whatever options you want with your LED Turn Signal Kit by using the drop down (∇) menus.

Looking for a SM LED Turn Signal Kit checkout our SM LED TSK #104.

Have you seen the new Polaris models?

About Cisco Folk

Hello, my name is Cisco Folk and I am the President of EZ Turn Signal Kits & Accessories here in Glendale, AZ. My passion is the outdoors, so I purchased a 2006 Polaris Ranger XP to help me get around. After using the old hang your arm out the side to signal oncoming traffic and almost being run over twice, I realized people do not know what hand signals are and I had enough. I wanted to install LED turn signals for my added safety. When I tried to purchase a four light LED turn signal kit, I was unable to find anyone who had developed an aftermarket LED Turn Signal Kit. As we all know the UTV's have small batteries, small charging systems and are generally driven in rough terrain. The main reasons why I wanted all LED turn signal lights are: Less current draw, resulting in increased battery & alternator life while allowing more power for other vehicle requirements. Faster illumination offers significant safety benefits for following drivers to react quicker, resulting in an average of a three foot reaction time advantage for every 10 miles per hour. LEDs have no filament, therefore are not susceptible to shock & vibration, a major cause of failure for lamps with incandescent bulbs. So, I created my own aftermarket LED Turn Signal Kit. I wanted DOT approved, good looking, clean and crisp LED lights, and ones that were very visible, even during the day. The LED Lights in my turn signal kits are not only bright, but they are hard wired with encapsulated electronics to eliminate corrosion. They have both the positive (+) and negative (-) wires to make a great connection, no screw through a metal surface to the frame for ground. You can hard wire the lights to both positive and negative, so you always have a good connection. I have seen several turn signal switches out there that come with a hose clamp, not this company. You will always get good looking, high quality aftermarket turn signals from EZ Turn Signal Kits!